Comparison of the ASTM D Method and the film thickness method for obtaining volume solids 3. Bibliography. Buy ASTM D R TEST METHOD FOR VOLUME NONVOLATILE MATTER IN CLEAR OR PIGMENTED COATINGS from SAI Global. proper ASTM standard for determining the volatile and non- volatile content of paint D Test Method for Volume Nonvolatile Matter in. Clear or Pigmented .
|Country:||Central African Republic|
|Published (Last):||24 September 2004|
|PDF File Size:||5.49 Mb|
|ePub File Size:||2.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
Determined directly by evaporating a known volume of an unfiltered water sample in a Deg C oven. Determine the specific gravity of the paint using mass per litre cup. Suspend the disc in water and weigh again. asm
Total dissolved solids – includes all solids present in a water sample filtered through a 1. Let see how may types of solids are there in liquid products or materials: Link to Active This link will always route to the current Active version of the standard.
Above the critical pigment volume concentration, the apparent volume of the dry film is significantly greater than theoretical due to the increase in unfilled voids between pigment particles. Total suspended solids – includes all solids present in a sample that remain on a 1. Can be performed on total, dissolved, or suspended samples to determine – total fixed solids, fixed dissolved solids, or fixed suspended solids.
Determined by filtering a known volume of sample and placing the filter and filter container in a Deg C oven for 24 hours to evaporate the water. An interlaboratory study to establish the precision of this test method included a water-reducible exterior latex paint and three automotive coatings that included a solvent-reducible primer surfacer, water reducible primer surfacer, water reducible enamel topcoat, and acrylic dispersion lacquer topcoat.
The values given in parentheses are for information only. Let it be W grams. Let it be W3, grams. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
One reason is that the volume occupied by a solution of resin in solvent may be the same, greater, or less than the total volume of the separate ingredients: These test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying and removing pressure-s This can be tested using IS – part Take Stainless Steel Disc 60 mm diameter and 0. Weigh the disc in air. Let it be P. Total solids – includes all solids present in a water sample.
I married on 30 th June having one baby Fixed solids – solids that remain after firing a sample in a Deg C muffle furnace. Historical Version s – view previous versions of standard. Weigh the coated disc in air.
Let see how to test the TSS:. Earlier collaborative studies included a gloss enamel, a flat wall paint, a gloss house enamel, an industrial baking enamel, an interior latex paint, and an exterior latex paint. Determined by evaporating a known volume of the filtrate sample in a Deg C oven.
This value is useful for comparing the coverage square feet of surface covered at a specified dry film thickness per unit volume obtainable with different coating products.
Suspend the coated disc in water and weigh again. Blot the coating material off the bottom edge of the disc so that beads or drops do not dry on the bottom edge of the disc.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Dip the disc in the paint sample for 10 minutes and take out the disc.
Allow the excess coating material to drain off. Technical – Volume solids or solid content. Let it be W4 grams. Let it be W1, grams.
Can be performed on total, dissolved, or suspended samples to determine – total volatile solids, volatile dissolved solids, or volatile suspended solids. Newer Post Older Post Home. Note the weight of the stainless-steel disc. The use of volume nonvolatile matter values in such instances should be carefully considered as the increased volume is largely due to air trapped in these voids.